J2 LED Accesories

Power, Cable, & Adapters

The J2 LED Lighting JTP (Jack to Plug) series:

This cable assembly is a commercial electronics grade interconnect for DC power distribution.  The design features DC power barrel connectors (2.1mm X 5.5mm) terminated with polarity color coded ferrules at mid-point for connection into a Euro style screw terminal block. Multiple cable assemblies can be connected in a daisy chain fashion to distribute power in a 12 volt DC lighting system.  The maximum current capacity is 3 amps with a total power of 36 watts in a 12 volt system.  The mid-point connection may be used to feed power into a dimmer. Alternatively, the cable assemblies may be used to interface directly to a power supply with a mating barrel connector and feed LED module strings directly from a mid-point connected terminal block.

Data-sheet: JTP1 Spec Sheet.pdf

The J2 LED Lighting PFC-F2.1X5.5-20:

Female DC barrel power connector pigtail. Intended for interconnect of 12 volt LED Lighting flex strips and accessories; dimmers, motion sensors, switch, etc. to power supplies. Also used with CCTV 12 volt camera systems to adapt to power supplies, etc. Characteristics

  • DC Barrel female connector to 20 inch ref. (500mm) black PVC jacketed cable with red and black wires.
  • LED Lighting low voltage applications rating: 3.0 amps at 12.0 volts (36 watts) continuous Max.
  • Operation usage temperature range: -20C to +60C (-4F to +140F)
  • Wire insulation: PVC
  • Wire gauge: 22 Awg
  • Female connector Jack accepts 2.1mm X 5.5mm Plug DC barrel connectors .
  • Data-sheet: PFC 2.1X5.5_20 Spec Sheet.pdf

    The J2 LED Lighting SMA (Switch Mode Adapter) series:

    Highly efficient DC power supplies.  The design features SMPS (Switched Mode Power Supply) circuit topology to optimize a low idle current and overall efficiency and size reduction. The power supplies contain standard USA blade type 120 VAC plugs which are changeable for other international power options within the 90-264 VAC range at 50-60 Hz. The 12 volt DC output cable is terminated with a barrel connector (2.1mm X 5.5mm). Our highest output model is the SMA1 which provides up to 3 amps at 12 volts for a maximum power of 36 watts continuous.  The power supplies meet the Energy Star Level V requirements for no load power consumption of 0.3 watts maximum for external power supplies.

    Data-sheet: SMA Power Supply Spec Sheet.pdf

    ATB ADAPTER PAIR LED LIGHTING ACCESSORIES 2.1 X 5.5 BARREL CONNECTOR 12 VOLTS DC series:

    A Male / Female pair of DC barrel power connector adapters. Intended for interconnect of 12 volt LED Lighting accessories; dimmers, motion sensors, switch, etc. to power supplies. Also used with CCTV 12 volt camera systems to adapt to power supplies, etc.

    Characteristics

  • DC Barrel Adapter Male / Female Pair to terminal block
  • LED Lighting low voltage applications rating: 3.0 amps at 12.0 volts (36 watts) continuous Max.
  • Operation usage temperature range: -20C to +60C (-4F to +140F)
  • Insulation: PVC
  • Recommended wire size for terminal block: 18 AWG stranded
  • Male adapter accepts 2.1mm X 5.5mm Jack DC barrel connectors.
  • Female adapter accepts 2.1mm X 5.5mm Plug DC barrel connectors.
  • J2 P/N: ATB-MF2.1X5.5
  • Data-sheet: ATB-MF2.1X5.5 Spec Sheet.pdf

    J2 P/N: RBC-18AWG-SJTW (Cable, LED Driver) Waterproof 2 conductor

    A bulk electrical / electronics grade black jacketed flexible interconnect cable with 18 Awg red / black conductors for DC power applications. This is a SJTW rated indoor / outdoor use cable that is waterproof and sunlight resistant. It has filler / separator material of cotton to maintain a round shape with flexibility and to aid in stripping.

    Specifications:

    Awg: 18 (2 PVC insulated conductors red and black), bare copper flexible 41 strand
    Amp: 10 Max.
    Volts: 300 max. AC
    System volts: 12 – 24 Typical.
    Flammability: VW-1 UL & CSA / FT2 CSA
    Certifications: UL component (Cable is marked UL)
    Maximum operating temperature: 105C Dry / 60C Wet
    Composition: Rohs / Pb-Lead free
    Filler / separator: cotton based thread and paper

    SJTW Type:

    SJ = Hard usage Flexible Cord (Trade Name = junior hard service cord)
    T = Thermoplastic insulation and jacket (PVC)
    W = Suitable for use in wet locations and sunlight resistant

    Dimensions:

    O.D. of Jacket Insulation: 7.4mm Typ.
    O.D. of inner conductor insulation: 2.8mm Typ.
    Intended for low voltage non-fixed, portable; power, lighting and solar panel applications.

    Applications include:

  • Outdoor/ indoor LED lighting
  • Commercial lighting
  • LED stage, studio and theater lighting
  • LED decorative lighting
  • Water feature low voltage LED lights
  • Standalone portable 12 volt solar panel systems and small wind turbine generators
  • Portable 12 volt battery packs
  • Low voltage DC extension power cables
  • Connecting low voltage luminaries
  • Power supply output cable assemblies
  • Equipment interconnect

  • The SJTW 18 Awg 2 conductor cable type is found as the low voltage output cable on many UL8750 / IP67 rated LED driver power supplies. For Constant Voltage (CV) and Constant Current (CC) LED driver types.

    Such as the below LED driver series:

  • Mean Well HLG-80, LRF HVGC- 100
  • Excelsys series LXC60
  • Thomas Research Products TRV-100
  • Inventronics EUC-036S
  • Data-sheet: SJTW Cable Spec Sheet.pdf

    Aplication-sheet: Cable Application Sheet.pdf